This may be circumstantial evidence, but I've noticed that when my machine cant get a WU (according to log entries), I will almost always get a WU right away if I reboot Windows.
Mark
Reboot causes folding work to appear
Moderators: Site Moderators, FAHC Science Team
-
JimboPalmer
- Posts: 2522
- Joined: Mon Feb 16, 2009 4:12 am
- Location: Greenwood MS USA
Re: Reboot causes folding work to appear
The longer the client runs without getting a Work Unit, the less often it asks for one.
After a reboot, the timer starts over.
It just checks more often after a reboot, for awhile.
After a reboot, the timer starts over.
It just checks more often after a reboot, for awhile.
Tsar of all the Rushers
I tried to remain childlike, all I achieved was childish.
A friend to those who want no friends
I tried to remain childlike, all I achieved was childish.
A friend to those who want no friends
-
Neil-B
- Posts: 1996
- Joined: Sun Mar 22, 2020 5:52 pm
- Hardware configuration: 1: 2x Xeon [email protected], 512GB DDR4 LRDIMM, SSD Raid, Win10 Ent 20H2, Quadro K420 1GB, FAH 7.6.21
2: Xeon [email protected], 32GB DDR4, NVME, Win10 Pro 20H2, Quadro M1000M 2GB, FAH 7.6.21 (actually have two of these)
3: [email protected], 12GB DDR3, SSD, Win10 Pro 20H2, GTX 750Ti 2GB, GTX 1080Ti 11GB, FAH 7.6.21 - Location: UK
Re: Reboot causes folding work to appear
A simpler way to have the same effect is to pause the client, wait a bit, then restart folding as this resets the retry timer ... Please don't overuse this - wait until the retry timer is at least 3-4 hours otherwise it just exacerbates the busy server problem.
2x Xeon E5-2697v3, 512GB DDR4 LRDIMM, SSD Raid, W10-Ent, Quadro K420
Xeon E3-1505Mv5, 32GB DDR4, NVME, W10-Pro, Quadro M1000M
i7-960, 12GB DDR3, SSD, W10-Pro, GTX1080Ti
i9-10850K, 64GB DDR4, NVME, W11-Pro, RTX3070
(Green/Bold = Active)
Xeon E3-1505Mv5, 32GB DDR4, NVME, W10-Pro, Quadro M1000M
i7-960, 12GB DDR3, SSD, W10-Pro, GTX1080Ti
i9-10850K, 64GB DDR4, NVME, W11-Pro, RTX3070
(Green/Bold = Active)
-
jrweiss
- Posts: 704
- Joined: Tue Dec 04, 2007 6:56 am
- Hardware configuration: Ryzen 7 5700G, 22.40.46 VGA driver; 32GB G-Skill Trident DDR4-3200; Samsung 860EVO 1TB Boot SSD; VelociRaptor 1TB; MSI GTX 1050ti, 551.23 studio driver; BeQuiet FM 550 PSU; Lian Li PC-9F; Win11Pro-64, F@H 8.3.5.
[Suspended] Ryzen 7 3700X, MSI X570MPG, 32GB G-Skill Trident Z DDR4-3600; Corsair MP600 M.2 PCIe Gen4 Boot, Samsung 840EVO-250 SSDs; VelociRaptor 1TB, Raptor 150; MSI GTX 1050ti, 526.98 driver; Kingwin Stryker 500 PSU; Lian Li PC-K7B. Win10Pro-64, F@H 8.3.5. - Location: @Home
- Contact:
Re: Reboot causes folding work to appear
Quitting and restarting the Client has the same effect.
Ryzen 7 5700G, 22.40.46 VGA driver; MSI GTX 1050ti, 551.23 studio driver
Ryzen 7 3700X; MSI GTX 1050ti, 551.23 studio driver [Suspended]
Ryzen 7 3700X; MSI GTX 1050ti, 551.23 studio driver [Suspended]
Re: Reboot causes folding work to appear
In the Advanced Control (FAHControl) you can also right click, and pause a slot, then wait a while, then start it again.jrweiss wrote:Quitting and restarting the Client has the same effect.
However this should only be done when the displayed "Next Attempt" for this particular slot is high (say, 1-2h)!
Either method should not be used excessively, it only causes more load on the already hard-pressed FAH server infrastructure.
CPU: Ryzen 9 3900X (1x21 CPUs) ~ GPU: nVidia GeForce GTX 1660 Super (Asus)